Dehi Pada Mondal
Dehi Pada Mondal
CSIR- Advanced Materials and Processes Research Institute
Verified email at
TitleCited byYear
Abrasive wear of Al alloy–Al2O3 particle composite: a study on the combined effect of load and size of abrasive
DP Mondal, S Das, AK Jha, AH Yegneswaran
Wear 223 (1-2), 131-138, 1998
Cenosphere filled aluminum syntactic foam made through stir-casting technique
DP Mondal, S Das, N Ramakrishnan, KU Bhasker
Composites Part A: Applied Science and Manufacturing 40 (3), 279-288, 2009
The effect of interlamellar spacing on strength of pearlite in annealed eutectoid and hypoeutectoid plain carbon steels
KK Ray, D Mondal
Acta metallurgica et materialia 39 (10), 2201-2208, 1991
Effect of interlamellar spacing on the mechanical properties of 0.65% C steel
OP Modi, N Deshmukh, DP Mondal, AK Jha, AH Yegneswaran, HK Khaira
Materials Characterization 46 (5), 347-352, 2001
Highly porous open cell Ti-foam using NaCl as temporary space holder through powder metallurgy route
N Jha, DP Mondal, JD Majumdar, A Badkul, AK Jha, AK Khare
Materials & Design 47, 810-819, 2013
Compressive deformation and energy absorption characteristics of closed cell aluminum-fly ash particle composite foam
DP Mondal, MD Goel, S Das
Materials Science and Engineering: A 507 (1-2), 102-109, 2009
Abrasive wear behaviour of a high carbon steel: effects of microstructure and experimental parameters and correlation with mechanical properties
OP Modi, DP Mondal, BK Prasad, M Singh, HK Khaira
Materials Science and Engineering: A 343 (1-2), 235-242, 2003
High stress abrasive wear behaviour of aluminium hard particle composites: Effect of experimental parameters, particle size and volume fraction
DP Mondal, S Das
Tribology international 39 (6), 470-478, 2006
Dry sliding wear behaviour of cast high strength aluminium alloy (Al–Zn–Mg) and hard particle composites
RN Rao, S Das, DP Mondal, G Dixit
Wear 267 (9-10), 1688-1695, 2009
Titanium-cenosphere syntactic foam made through powder metallurgy route
DP Mondal, JD Majumder, N Jha, A Badkul, S Das, A Patel, G Gupta
Materials & Design 34, 82-89, 2012
Synergic effect of reinforcement and heat treatment on the two body abrasive wear of an Al–Si alloy under varying loads and abrasive sizes
S Das, DP Mondal, S Sawla, N Ramakrishnan
Wear 264 (1-2), 47-59, 2008
Effect of SiC addition and running-in-wear on the sliding wear behaviour of Al–Zn–Mg aluminium alloy
DP Mondal, S Das, RN Rao, M Singh
Materials Science and Engineering: A 402 (1-2), 307-319, 2005
Dry sliding wear behaviour of aluminum syntactic foam
DP Mondal, S Das, N Jha
Materials & Design 30 (7), 2563-2568, 2009
Effect of strain rate and relative density on compressive deformation behaviour of closed cell aluminum–fly ash composite foam
DP Mondal, MD Goel, S Das
Materials & Design 30 (4), 1268-1274, 2009
Dynamic compression behavior of cenosphere aluminum alloy syntactic foam
MD Goel, M Peroni, G Solomos, DP Mondal, VA Matsagar, AK Gupta, ...
Materials & Design 42, 418-423, 2012
Correlation of abrasive wear with microstructure and mechanical properties of pressure die-cast aluminum hard-particle composite
S Das, DP Mondal, G Dixit
Metallurgical and Materials Transactions A 32 (3), 633-642, 2001
Effect of heat treatment on the sliding wear behaviour of aluminium alloy (Al–Zn–Mg) hard particle composite
RN Rao, S Das, DP Mondal, G Dixit
Tribology international 43 (1-2), 330-339, 2010
Effect of SiC concentration and strain rate on the compressive deformation behaviour of 2014Al-SiCp composite
DP Mondal, NV Ganesh, VS Muneshwar, S Das, N Ramakrishnan
Materials Science and Engineering: A 433 (1-2), 18-31, 2006
Sliding wear behaviour of aluminum syntactic foam: A comparison with Al–10 wt% SiC composites
N Jha, A Badkul, DP Mondal, S Das, M Singh
Tribology International 44 (3), 220-231, 2011
Influence of SiC particles addition on the corrosion behavior of 2014 Al–Cu alloy in 3.5% NaCl solution
IB Singh, DP Mandal, M Singh, S Das
Corrosion Science 51 (2), 234-241, 2009
The system can't perform the operation now. Try again later.
Articles 1–20